If you don’t see an answer to your question below, please don't hesitate to contact us at firstname.lastname@example.org or call us at (704) 815-1611, Monday – Friday, 8 a.m. – 5 p.m.
Rule number one is to always leave some paper towel hanging out when closing the door of the dispenser. That’s because once the door is closed, the internal sensor looks for the sheet of paper towel that should be hanging out. If it’s not there, the sensor thinks the dispenser is empty. See the operation video here for a quick overview of how to use the dispenser. Spoiler alert: it’s easy.
It’s still in “training mode”. “Training mode” occurs when you first close the door of the dispenser after installing a roll of paper towels. The dispenser retracts the paper towel you left hanging out, and when you place your hand in front of the sensor it will dispense a length longer than a full sheet paper towel. This is “training mode”. It is at this point you “teach” the dispenser what length to always dispense. Tear off the towel at the perforation of your desired length. The dispenser measures what it retracts after you take the towel and “knows” from that point forward to give you paper towels in that size increment. See the operation video here.
The dimensions are as follows: 14.6 inches wide x 9.6 inches deep x 7.6 inches high. You can see a diagram of the dimensions on the second page of our information sheet here (PDF).
It should. The dispenser was designed to fit beneath the smallest standard cabinet available. If you have custom cabinets, or are still unsure, check the dimensions of the dispenser on our information sheet here (or look at the question above).
Quite simply. If you can, please review our installation video here. The gist of the process is this: using the included template, you mount the dispenser’s bracket beneath your cabinet with the 8 included eighth-inch screws (the screws are tiny enough that they should not break through the base of your cabinet - but you should measure to make sure). Once the bracket is in place, align the dispenser’s 4 posts with the 4 holes in the bracket. Slide the dispenser left or right to center it. That’s it.
Yes, under cabinet lighting can be an issue. Depending on the type of lighting you have, it may be possible to remove a strip of it and install a shorter strip, accommodating for the dispenser. Another option is to remove the strip lighting from beneath the cabinet under which you plan to install the dispenser and use the puck-shaped lighting instead. We’ve also had customers install thin-strip LED lights.
That’s easy: any standard paper towels that have perforated lengths of any size. In other words, any paper towels you can buy in the grocery store or supermarket should work just fine (see the question below for the one exception). Please do keep in mind that exorbitantly large rolls may not fit at first. A good rule of thumb is if the roll is so big it looks silly, then it probably won’t fit.
Ah, Viva®. We do love your cottony softness but it’s the way your sheets cling to the roll that’s not working with the dispenser. To see what we mean, take a roll of Viva® and start unwrapping the roll. See? The sheets sort of cling together. Not that there’s anything wrong with that; it just doesn’t play nice in our dispenser. If you’re determined however, read in the next question about flipping over the roll.
Well, that could be a couple of things. Firstly, make sure you round out the roll if it’s squished. Take out the roll of paper towels and look at it from the side. If the cardboard roll is not as circular as it could be, try and round it out a bit. Doing that should greatly improve performance. If you are still having an issue, another tip would be to flip the roll over in the dispenser so that it distributes upside down (so to speak). Both the “overhand” and “underhand” method of installing the roll of paper towels work equally well.
Absolutely not. The sensor’s reach is just 2 to 3 inches and rapid movement doesn’t trigger it. You must place your hand close to the sensor itself to break its beam and trigger the dispenser. The sensor was designed to avoid accidental dispenses. If you think about it, if you do accidentally dispense a towel: don’t take it. It’ll retract. Nice.
This is the sign of dust blocking the lens of the internal sensor. This is an easy fix if it does happen (it’s actually quite rare). First unplug the dispenser (if it is plugged in). Then remove the dispenser from beneath the cabinet by sliding it left or right and dropping it down from its bracket. Place the dispenser top-down on a table in front of you. Open the door of the dispenser and look at the upper-half. You’ll see a tiny square hole leading to the sensor (see picture below). Simply blow into the hole to remove any debris or dust. That’s it. Reattach the dispenser to its bracket beneath your cabinet and try it again. It should function just fine moving forward.
Good question. The different sizes of posts (the cylindrical pieces of plastic that are located on top of the dispenser) are included to lower the dispenser to accommodate for different sizes of fascia (the decorative paneling attached to the bottom of your cabinet). Not all cabinets have fascia board, but if yours does it could potentially block the sensor of the dispenser. Simply hold the dispenser up under the cabinet to see if the fascia will block the sensor. If it doesn’t, feel free to use any size posts you wish.
Ah, those are locking keys that were a late addition to the parts included with the dispenser. The original use and intent of these keys were to keep the dispenser in place once you’ve installed it. Once the dispenser in place under your cabinet, open the dispenser and look inside at the very middle-top. There’s a hole there in which you insert one of the locking keys to “lock” the dispenser in place. The length of key is determined by the length of the posts you used for the installation. Use the smallest key if you didn’t change the factory-installed posts. Once the key is inserted, you will be unable to shift the dispenser left or right to drop it down from its bracket. We’ve determined that these are unnecessary pieces and you can safely install your dispenser without using them.